Solo Implants

main page site map feedback

+49 5624 7579890

 
 
 


Learn more about the surface

The idea of an one stage implantation and immediate loading on the orthopaedic constructions set on implants lately gets the greater popularity among the stomatologists. This can be easier explained by the advantages given by the one stage implantation and immediate loading. Absence of the second operation stage, the possibility of temporal construction setting right after the operation allows to reduce the terms of treatment, and to bring down discomfort of a patient also.

Osteointegration and favourable long-term result is attainable during the implants setting with the use of noninvasive surgical methodology, eliminating mobility of implants right after their setting, and during the implants stabilization period so that the rendered loading will not cause the mobility during the functioning.

Clinical terms for implementation of the one stage implantation are as following:

  • It is the good value bone (I or II type);
  • It is the adequate width and bone height (this is sufficient for 3,5 millimeters in diameter and 15 millimeters length of the implant setting;
  • It is the adequate fastened gingiva zone (not less than 3 millimeters);
  • It is the presence of nearby teeth, that would protect an implant from the occlusal loading and exclude it by this way from a function able to cause mobility;
  • It is the possibility of fully implant stabilization in the moment of setting.

During the one stage implants setting a shred is thrown aside first of all and then a bed is prepares for implant of necessary diameter and length introduction on standard methodology. The doctor can use the temporal removable prosthetic appliance preliminary in the esthetically important area drilled beforehand in order to avoid the loading on the engrafting implant.

Since the one stage implantation has begun to be used in practice conservatively and successfully, the attempts of immediate prosthetic repair became a next step. Ере conception of immediate prosthetic repair consists in attachment of the fixed temporal prosthetic appliances coming right after the implants setting. This is not new now. The new thing is that it is possible to avoid the most tearing away during the one stage implantation, if carefully follow some key requirements.

We will mark that the one stage implantation and immediate prosthetic repair are indicated not only at healthy presence (beginning to live) alveolar comb. There is possibility to set implants in small holes often right after the extraction at the exodontia of lower jaw, then to fix the abutments, to take in shreds and to cement the temporal prosthetic appliance. The implants must be longer than roots of teeth in this case, improving the correlation of bone in and bone out part of construction which provides the best stability.

Let us discuss finally the possibility of the so-called flapless methodology using or implants setting without the throwing aside of shred, that always have resulted afterwards in the necessity of guy-sutures imposition. Absence of flaps reduces the discomfort of patients in a postoperative period. This methodology, moreover, allows to provide the best blood supply for the area, reducing probability of bone resorption, abandoning the periosteum intact from the vestibular and oral side of comb.

It is necessary to apply a perforator during the use of this methodology without throwing aside the flap for the gingiva removal above the edge of comb in the area of implant setting. The clinician is recommended to measure vestibular-oral bone distance in three points before the perforator application by means of osteometr: comb apex, middle area of the supposed implant, apex area of the supposed implant.

The similar measuring can allow the tapping of the cavities presence on the bone surface. If the cavity more than 15 degrees was found out it is recommended to throw aside shreds on traditional methodology for providing the best visualization while the implant setting. It is indicated to delete a gingival cork and to bare the bone by means of perforator and curette in case of expressed inside pressure absence. Use the spherical coniferous forest for the cortical plate penetration and after it use the pilot drill. Then implant setting on standard methodology is conducted.

The implant setting methodology without throwing aside of shred is possible to apply in combination with the one stage setting or immediate prosthetic repair. It is necessary to take into the account a few additional factors along with principles that must be followed at the both methodologies implementation, in case of implant setting without flap throwing aside. They are as following:

  • It is the presence of tissue keratinization greater zone (5 millimeters, at least), as this methodology implies the excision of some fastened gingiva quantity;
  • It is the presence of greater bone width (4,5 millimeters, at least) in the default of 15 degrees inside pressure.

As compared to traditional methodology, the visualization is mionectic, that is the reason why it is more difficult to make sure that the implant is set on the comb middle. The large width of comb provides to the clinician the large freedom of actions.

If the clinical situation is correctly estimated the one stage implantation and immediate prosthetic repair without throwing aside of shred are the reliable methods of treatment and have the considerable advantages for patients.

The one stage implantation, immediate prosthetic repair and setting of implants, without throwing the flap aside can have a high coefficient of engraftment, comparable with the results of a traditional two stage implants setting methodology with the correct choice of patients, who have a good bone value of keratinization gingiva adequate zone, which has sufficient height and breadthways alveolar sprout. All methodologies promote probability of patient consent receipt because of declining the discomfort and reducing the treatment general term.

Features

The "Solo" implant series form geometry assists the ideal implant setting. It is possible to remark the features of this series as following:

  • It is the monolithic structure of Grade 4 brand titan;
  • It is the self-cutting carving and excellent primary stability, as a result;
  • It is the noninvasive implant introduction with minimum effort;
  • It is the compression of bone tissue in all implant directions and all length;

shallow precervical carving which provides the optimal partition of load and more subzero indexes of tension by comparison to analogical constructions.

Sizes

One-stage implants with spherical head

Length, mm Diameter, mm
10 2,5; 3; 3,5
13
15

Onestage implants with conical head

Length, mm Diameter, mm
10 2,5; 3; 3,5
13
15

 

Manual